our products

D&Q Mining is a high-tech company integrating R&D, production and sales. It provides mature products and solutions such as crushers, sand making, milling equipment, mobile crushing stations, etc., for aggregate, mining and waste recycling.

diy concrete leveling foam

3 Simple Ways to Permanently Raise Concrete with Foam NOW!

Locate the dips, Get the right equipment and foam.,use 5/8-inch masonry bit to drill a hole through the concrete, and spray the foam into it. The foam will expand and harden, filling the void in the ground and leveling the driveway.

More

This Spray Foam Will Fix Any of Your Concrete Problems

Apr 21, 2018· The first step is to drill holes in the problem concrete. Holes should be no less than six inches away from the edge of the concrete. Once the holes have been set, the Geolift is injected in between the concrete and the dirt. The foam will fill up the parts of the concrete that are uneven and will raise it to the proper height.

More

How to Raise Concrete With Foam Hunker

The method leaves no sign of the foam behind, resulting in a level slab that should remain level for years to come. Step 1 Locate the point at which the slab begins to sink into the soil by placing a carpenter's level onto the surface of the slab and moving it from the level section toward the sagging edge.

More

Raising and Leveling Concrete Slabs in Minutes with

Jun 20, 2014· redeemersgroup 1-877-619-4491 Watch PolyLEVEL in action and see in real time how it is used to quickly and safely lift a sinking sidewalk! P...

More

Making Foam Concrete FoamConcreteWorld

DIY Foam. Making foam from household products such as soft soap or shampoo is not recommended if you can get hold of special FC foam. The cost of even the most expensive foam agents is small compared to the cost of a failed foam concrete batch or whole house! The biggest problem for the DIY is obtaining a small quantity of agent.

More

Foam Injection Leveling Mr. Sidewalk

When you level your uneven concrete using poly foam concrete raising techniques, ⅝” injection holes (Size of a dime!) are strategically drilled around the areas where the concrete is sunken and requires lifting. 2. The concrete raising equipment is contained in our custom trailer, and has a sufficient length of hose to accommodate most

More

Concrete Lifting for the Do It Yourselfer DoItYourself

Concrete Lifting with a Small Sledge Hammer, Brick Chisel, and Drill. This is another method for doing it yourself. Use the brick chisel and sledgehammer to undercut any edges of the sunken concrete as necessary. With a concrete drill or masonry bit, drill small holes into the sunken area and slowly pour a thin mixture of cement into the holes. Allow it to stand for half an hour so that it can settle.

More

Do-It-Yourself Concrete Jacking Hunker

The concrete jacking process concludes with capping the holes drilled through the slab once the slab reaches the desired height and is verified as level. Cap the holes with grout and allow them to dry. You can make the effect less obvious by taking a small amount of the dust produced while drilling the holes and adding it to the grout mix.

More

Do it yourself Concrete lifting? : HomeImprovement

Aug 18, 2008· Do it yourself Concrete lifting? Anyone know of any way to raise a large slab of concrete just about an inch. The city says I need to replace a part of my driveway because of "trip hazard" The difference in height is just 3/4 of an inch.

More

Making Foam Concrete FoamConcreteWorld

DIY Foam. Making foam from household products such as soft soap or shampoo is not recommended if you can get hold of special FC foam. The cost of even the most expensive foam agents is small compared to the cost of a failed foam concrete batch or whole house! The biggest problem for the DIY is obtaining a small quantity of agent.

More

Foam Injection Concrete Leveling

Foam injection concrete leveling can be done quickly, with the surface being usable immediately. Injection hole sizes (5/8-inch, or about the size of a dime) are smaller than our stone slurry grout leveling holes, potentially making it a good solution for highly visible areas or decorative concrete surfaces.

More

Concrete Lifting and Slab Jacking Profoam

Concrete raising can usually be done for less than half the cost of pouring new concrete. However, the savings may be even greater, since when concrete raising the costs of demolition, removal, and landscaping are eliminated. Polyurethane foam concrete lifting and stabilization avoid costly tear out and disruptive replacement of the slab.

More

What you NEED to Know About Concrete Lifting Foams HMI

Jul 12, 2012· “Not Every Like Foam Is the Same” Concrete Lifting Foam is Concrete Lifting FoamRight? There are special characteristics you need to look for when deciding what polyurethane foam to use for lifting and leveling concrete. Expansion is important, but what about set-up and cure times or adhesion? In this blog, we are going to explore the truth about polyurethane concrete lifting foam

More

PolyLevel Concrete Leveling Indiana Foundation Service

PolyRenewal concrete leveling is an expansive, polyurethane foam that is injected underneath sunken concrete slabs. Small holes are drilled through the sunken concrete slab and the pressurized PolyRenewal foam is sprayed into the hole through a specialized hose and nozzle. The foam quickly expands to fill any empty space below the slab.

More

Concrete Leveling & Slab Lifting Little Rock, Arkansas

Repairing your concrete with polyjacking is a quick and affordable alternative to replacing it sometimes being less than half the cost. How We Use Polyjacking for Concrete Leveling. Polyjacking is a concrete repair method that uses polyurethane foam to raise, level, and permanently stabilize concrete surfaces. Small holes are drilled into the

More